|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
74VCXH162373 LOW VOLTAGE CMOS 16-BIT D-TYPE LATCH (3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS s s s s s s s s s s 3.6V TOLERANT INPUTS AND OUTPUTS HIGH SPEED : tPD = 3.3 ns (MAX.) at VCC = 3.0 to 3.6V tPD = 4.5 ns (MAX.) at VCC = 2.3 to 2.7V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0V |IOH| = IOL = 8mA (MIN) at VCC = 2.3V 26 SERIE RESISTOR IN OUTPUTS OPERATING VOLTAGE RANGE: VCC(OPR) = 2.3V to 3.6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES H162373 BUS HOLD PROVIDED ON DATA INPUTS LATCH-UP PERFORMANCE EXCEEDS 300mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V TSSOP ORDER CODES PACKAGE TSSOP TUBE T&R 74VCXH162373TTR PIN CONNECTION DESCRIPTION The 74VCXH162373 is a low voltage CMOS 16 BIT D-TYPE LATCH with 3 STATE OUTPUTS NON INVERTING fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 2.3 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. These 16 bit D-TYPE latches are bite controlled by two latch enable inputs (nLE) and two output enable inputs (OE). While the nLE input is held at a high level, the nQ outputs will follow the data input precisely. When the nLE is taken low, the nQ outputs will be in a normal logic state (high or low logic level) and while high level the outputs will be in a high impedance state. Bus hold on data inputs is provided in order to eliminate the need for external pull-up or pull-down resistor. The device circuits is including 26 series resistance in the outputs. These resistors permit to reduce line noise in high speed applications. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. February 2003 1/12 74VCXH162373 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1 SYMBOL 1OE NAME AND FUNCTION IEC LOGIC SYMBOLS 3 State Output Enable Input (Active LOW) 2, 3, 5, 6, 8, 9, 1Q0 to 1Q7 3-State Outputs 11, 12 13, 14, 16, 17, 2Q0 to 2Q7 3-State Outputs 19, 20, 22, 23 24 2OE 3 State Output Enable Input (Active LOW) 25 2LE Latch Enable Input 36, 35, 33, 32, 2D0 to 2D7 Data Inputs 30, 29, 27, 26 47, 46, 44, 43, 1D0 to 1D7 Data Inputs 41, 40, 38, 37 48 1LE Latch Enable Input 4, 10, 15, 21, GND Ground (0V) 28, 34, 39, 45 7, 18, 31, 42 VCC Positive Supply Voltage TRUTH TABLE INPUTS OE H L L L LE X L H H D X X L H OUTPUT Q Z NO CHANGE * L H X : Don`t Care Z : High Impedance * : Q outputs are latched at the time when the LE input is taken low logic level. 2/12 74VCXH162373 LOGIC DIAGRAM This logic diagram has not to be used to estimate propagation delays ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage (OFF State) DC Output Voltage (High or Low State) (note 1) DC Input Diode Current DC Output Diode Current (note 2) DC Output Current Parameter Value -0.5 to +4.6 -0.5 to +4.6 -0.5 to +4.6 -0.5 to VCC + 0.5 - 50 - 50 50 100 400 -65 to +150 300 Unit V V V V mA mA mA mA mW C C ICC or IGND DC VCC or Ground Current per Supply Pin PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND, VO > VCC RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO VO IOH, IOL IOH, IOL Top dt/dv Supply Voltage Input Voltage Output Voltage (OFF State) Output Voltage (High or Low State) High or Low Level Output Current (VCC = 3.0 to 3.6V) High or Low Level Output Current (VCC = 2.3 to 2.7V) Operating Temperature Input Rise and Fall Time (note 1) Parameter Value 2.3 to 3.6 -0.3 to 3.6 0 to 3.6 0 to VCC 12 8 -55 to 125 0 to 10 Unit V V V V mA mA C ns/V 1) VIN from 0.8V to 2V at VCC = 3.0V 3/12 74VCXH162373 DC SPECIFICATIONS (2.7V < VCC < 3.6V unless otherwise specified) Test Condition Symbol Parameter VCC (V) -40 to 85 C Min. 2.0 2.7 to 3.6 0.8 2.7 to 3.6 2.7 3.0 VOL Low Level Output Voltage 2.7 to 3.6 2.7 3.0 II II(HOLD) Input Leakage Current Input Hold Current 2.7 to 3.6 3.0 3.6 Ioff IOZ Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input 0 2.7 to 3.6 IO=-100 A IO=-6 mA IO=-8 mA IO=-12 mA IO=100 A IO=6 mA IO=8 mA IO=12 mA VI = VCC or GND VI = 0.8V VI = 2V VI = 0 to 3.6V VI or VO = 0 to 3.6V VI = VIH or VIL VO = 0 to 3.6V VI = VCC or GND 2.7 to 3.6 2.7 to 3.6 VI or VO = VCC to 3.6V VIH = VCC - 0.6V 75 -75 500 10 10 20 20 750 VCC-0.2 2.2 2.4 2.2 0.2 0.4 0.55 0.8 5 75 -75 500 10 10 20 20 750 A A A A A VCC-0.2 2.2 2.4 2.2 0.2 0.4 0.55 0.8 5 A V V 0.8 Max. Value -55 to 125 C Min. 2.0 V Max. Unit VIH VIL VOH High Level Input Voltage Low Level Input Voltage High Level Output Voltage ICC ICC 4/12 74VCXH162373 DC SPECIFICATIONS (2.3V < VCC < 2.7V unless otherwise specified) Test Condition Symbol Parameter VCC (V) -40 to 85 C Min. 1.6 2.3 to 2.7 0.7 2.3 to 2.7 2.3 VOL Low Level Output Voltage 2.3 to 2.7 2.3 II II(HOLD) Ioff IOZ Input Leakage Current Input Hold Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current 2.3 to 2.7 2.3 0 2.3 to 2.7 IO=-100 A IO=-4 mA IO=-6 mA IO=-8 mA IO=100 A IO=6 mA IO=8 mA VI = 0 to 3.6V VI = 0.7V VI = 1.7V VI or VO = 0 to 3.6V VI = VIH or VIL VO = 0 to 3.6V VI = VCC or GND 2.3 to 2.7 VI or VO = VCC to 3.6V 45 -45 10 10 20 20 VCC-0.2 2.0 1.8 1.7 0.2 0.4 0.6 5 45 -45 10 10 20 20 A VCC-0.2 2.0 1.8 1.7 0.2 0.4 0.6 5 A A A A V V 0.7 Max. Value -55 to 125 C Min. 1.6 V Max. Unit VIH VIL VOH High Level Input Voltage Low Level Input Voltage High Level Output Voltage ICC DYNAMIC SWITCHING CHARACTERISTICS (Ta = 25C, Input tr = tf = 2.0ns, C L = 30pF, RL = 500) Test Condition Symbol Parameter VCC (V) 2.5 3.3 2.5 3.3 2.5 3.3 VIL = 0V VIH = VCC VIL = 0V VIH = VCC VIL = 0V VIH = VCC Value TA = 25 C Min. Typ. 0.25 0.35 -0.25 -0.35 2.05 2.65 Max. V V V Unit VOLP VOLV VOHV Dynamic Low Voltage Quiet Output (note 1, 3) Dynamic Low Voltage Quiet Output (note 1, 3) Dynamic High Voltage Quiet Output (note 2, 3) 1) Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 2) Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the HIGH state. 3) Parameters guaranteed by design. 5/12 74VCXH162373 AC ELECTRICAL CHARACTERISTICS (CL = 30pF, RL = 500, Input tr = tf = 2.0ns) Test Condition Symbol Parameter VCC (V) 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 -40 to 85 C Min. 1.0 0.8 1.0 0.8 1.0 0.8 1.0 0.8 1.0 1.0 1.0 1.0 1.5 1.5 Max. 4.5 3.3 4.9 3.6 5.4 3.9 4.4 4.0 Value -55 to 125 C Min. 1.0 0.8 1.0 0.8 1.0 0.8 1.0 0.8 1.0 1.0 1.0 1.0 1.5 1.5 Max. 5.2 4.0 5.7 4.2 6.2 4.7 5.1 4.8 ns ns ns ns ns ns ns 0.5 0.5 ns Unit tPLH tPHL tPLH tPHL tPZL tPZH tPLZ tPHZ ts th tw Propagation Delay Time Dn to Qn Propagation Delay Time LE to Qn Output Enable Time Output Disable Time Setup TIme, HIGH or LOW level Dn to LE Hold Time High or LOW level Dn to LE LE Pulse Width, HIGH tOSLH tOSHL Output To Output Skew Time (note1, 2) 0.5 0.5 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) 2.5 or 3.3 2.5 or 3.3 2.5 or 3.3 VIN = 0 or VCC VIN = 0 or VCC fIN = 10MHz VIN = 0 or VCC Value TA = 25 C Min. Typ. 6 7 20 Max. pF pF pF Unit CIN COUT CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per circuit) 6/12 74VCXH162373 TEST CIRCUIT TEST tPLH, tPHL tPZL, tPLZ (VCC = 3.0 to 3.6V) tPZL, tPLZ (VCC = 2.3 to 2.7V) tPZH, tPHZ CL = 30 pF or equivalent (includes jig and probe capacitance) RL = R1 = 500 or equivalent RT = ZOUT of pulse generator (typically 50) SWITCH Open 6V 2VCC GND WAVEFORM SYMBOL VALUES Symbol 3.0 to3.6V VIH VM VX VY 2.7V 1.5V VOL + 0.3V VOH - 0.3V VCC 2.3 to 2.7V VCC VCC/2 VOL + 0.15V VOH - 0.15V 7/12 74VCXH162373 WAVEFORM 1 : LE TO Qn PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn TO LE SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 8/12 74VCXH162373 WAVEFORM 3 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) 9/12 74VCXH162373 TSSOP48 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0 0.50 6.0 0.5 BSC 8 0.75 0 0.020 0.17 0.09 12.4 8.1 BSC 6.2 0.236 0.0197 BSC 8 0.030 0.05 0.9 0.27 0.20 12.6 0.0067 0.0035 0.488 0.318 BSC 0.244 TYP MAX. 1.2 0.15 0.002 0.035 0.011 0.0079 0.496 MIN. TYP. MAX. 0.047 0.006 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 7065588C 10/12 74VCXH162373 Tape & Reel TSSOP48 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 8.7 13.1 1.5 3.9 11.9 12.8 20.2 60 30.4 8.9 13.3 1.7 4.1 12.1 0.343 0.516 0.059 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 1.197 0.350 0.524 0.067 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch 11/12 74VCXH162373 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. (c) http://www.st.com 12/12 |
Price & Availability of 74VCXH162373 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |